Cold Weather is Here Again!

            Once again, the weather has turned and cooler temperatures are starting to become the norm.  With the arrival of cold weather comes the use of heat producing appliances to keep our homes and businesses warm.  If you haven’t already done so, it is recommended that you engage a reputable heating and air conditioning company to service your furnace or heat pump and make sure that it is working properly before the really cold weather settles in.  For those of you that undertake that job personally, there are a few things that you should bear in mind.  When you take the service access panels off, be prepared to clean the motor and blower thoroughly.  Use a brush (a paint brush works fine) to clean inside the air openings of the motor and blower louvers.  Once you’ve dusted the air handling section, use the blower end of a shop vac (if available) to blow all of the dust out of the air handler.  If you don’t have a shop vac, use a standard vacuum cleaner and suck out as much dust as possible.  Lint and dirt buildup can burn and help to spread a fire, particularly if the furnace is started, allowed to operate, and service ignored for several seasons.  With heat pumps, air has to be able to flow freely through the inside and outside coils and therefore, has to be free of and any trash and debris that might have accumulated during the summer.  As with gas fired units, the air handler also has be cleaned and kept free of dust and lint.  Air filters should be replaced at the beginning of each heating (and cooling) season and inspected at least once per month.  Filters should be replaced when you can’t see through the media.  If you can’t see through the filter media, then air is being restricted enough to affect the heating (and cooling) capacity. 

            Aside from standard heating units, there are those that use kerosene or propane gas heaters.  In addition to a through cleaning, care must be taken to remember that small, fuel burning, space heaters and some gas log appliances are NOT VENTED.  As a result, they will produce CARBON MONOXIDE, a deadly, toxic gas.  Since these appliances are not vented, carbon monoxide is released into the space being heated.  DO NOT go to sleep with one of these types of appliances in operation.  Death from asphyxiation is a likely result.  Symptoms of carbon monoxide poisoning include headache, nausea, and vomiting.  Victims of carbon monoxide poisoning should be evacuated to the outdoors as quickly as possible while awaiting ambulance service.  Moreover, if you have to use a portable generator because of a power outage, remember, the danger of carbon monoxide poisoning is still present if the generator is operating inside the home or garage.  If using a small electric heater, a through cleaning is also required.  The main thing to remember when using space heaters, whether fuel burning or electric, is to keep them far enough away from combustible materials.  The heaters usually come with operating instructions that discuss how far from combustible material the heater can be placed.  However, the operating instructions are usually misplaced, discarded, or lost.  If you can’t remember how far away to place a heater, generally, a three foot distance is usually far enough away to keep most combustible material cool enough to keep it from igniting.  However, if the material feels too warm at a three foot distance, then move the heater back to increase the distance until the material feels cool.  USE COMMON SENSE! 

Fires and Appliance Safety

The weather has definitely gotten colder and heating systems are being put to the test. There are different kinds of systems; electric resistance, gas-fired forced air, hot water, and steam to name a few.  Regardless of the type of system, the potential for accidental fire is part of all heating systems.   During this time of year, it not uncommon for problems to develop which, when left unattended, can result in significant damage to homes and businesses.  For example, furnaces, both gas and electric, should be cleaned at least once per year; at the beginning of the heating season.  Some people think that just because they change their air filters every once-in-awhile maintenance is complete.  NOT SO!  Depending on the efficiency of the filter in use, some dust particles will pass through the filter media and accumulate on blower blades, motors, and heat exchanger surfaces.  The burning smell often detected when the furnace is first started is the result of dust accumulation.  If the furnace is never cleaned, dust accumulation can ignite and spread outside of ductwork.  Similarly, if the controls area is never cleaned, burners can become clogged resulting in poor combustion and sometimes, delayed ignition.  Delayed ignition of gas/air mixtures can become explosive and when ignited, can release a tremendous amount of heat with deadly force.  Poor combustion can also produce carbon monoxide which when inhaled can be deadly, especially to elderly people and young children with respiratory problems.  Similarly, electric heating systems such as heat pumps should be checked for proper operation as well as components that are in good working condition.  One of the biggest problems that should be guarded against is the wiring insulation that becomes brittle with age and cracks.  Exposure of conductors can result in short circuiting leading to a fire which can then spread to the structure.  Just because a circuit is protected with a circuit breaker doesn’t mean that a fire can never develop.  Circuit breakers are current limiting devices NOT thermal limiting devices.  Heat exchange coils, motor, fans, and blowers in heat pumps should also be kept clean.  Heat pumps come in different configurations such as air to air, air to water, and air to ground.  In the last two configurations, a fluid such as water or glycol is circulated to transfer heat to or from the heat pump.  In order to do so, a pump is used to circulate the fluid and must also be serviced at certain times.  Failure to do so can result in pump motor burnouts that could result in fire.  Remember, the pump and its motor are usually two separate components unless intentionally manufactured as a single unit.  Lastly, there is not much that can be done with hot and steam boilers except to make sure that the wiring is in good condition, stack temperature is not excessive, and piping is also in good condition.  Also, remember that piping can also be a source of ignition.  Hot piping can ignite combustibles if contact is maintained long enough.  Maintenance is the key to preventing fires in heating equipment.